Zine folding guide

How to Fold a
One-Sheet 8-Page Zine.

Fold one printed sheet into eight panels, cut one slit through the middle, then push it into a plus and flatten it into a booklet. Here is every move, one motion at a time.

1 printed sheetScissorsA few quiet minutes

Follow along

How to fold a zine, step by step.

Fold it like you mean it. The better your creases, the better your zine will turn out.

01 / 11

01

Start with one printed sheet.

Lay the sheet landscape on the table, printed side up, with the back and front covers in the bottom-left corner. The top row of pages is printed upside down on purpose.

A single landscape sheet marked with eight zine panels.

02 / 11

02

Turn and flip the sheet.

Rotate it 90 degrees counterclockwise so it stands tall, then flip it over along its long edge. The printed side now faces the table.

The sheet rotates counterclockwise and flips over.

03 / 11

03

Fold the short way.

Bring the two short ends together and press the crease firmly with your thumbnail. Then unfold the sheet again.

The paper folds in half across its short side, then opens flat.

04 / 11

04

Rotate, fold the long way.

Turn the paper clockwise, fold it in half the long way, sharpen the crease, and open it back out. This long crease is the one you will cut along later.

The sheet rotates, folds lengthwise, and opens flat again.

05 / 11

05

Bring both ends to the middle.

Turn the sheet counterclockwise, then fold each end inward until it meets the center crease. These two creases become the edges of your pages, so make them sharp.

Both outer ends of the sheet fold inward to meet at the middle.

06 / 11

06

Open, turn, and flip.

Open both ends. As you do, turn the sheet counterclockwise and flip it over the short edge. It should end up how you started.

The folded ends open as the sheet turns and flips over.

07 / 11

07

Fold it, then turn it.

Fold the sheet in half and lift it off the table. Rotate the folded packet a quarter turn counterclockwise so it is ready to cut.

The sheet folds in half, lifts, and turns counterclockwise.

08 / 11

08

Make the cut.

Cut along the middle crease, from the folded edge to the center of the paper, and stop where it meets the crossing crease. Don't go too far!

Scissors cut a short slot along the center crease of the folded paper.

09 / 11

09

Turn and open.

Rotate the cut sheet back clockwise, unfold it, and lower it flat onto the table. You should see one slit across the middle two panels, with the end panels still joined.

The cut sheet turns back, opens, and lowers flat onto the table.

10 / 11

10

Fold and push.

Fold it in half the long way with the printed side out. Hold both ends and push them together until the slit opens into a plus sign.

The cut sheet folds and the ends push together, opening the center into a cross.

11 / 11

11

Flatten and close.

Flatten the inside, then fold the stack around its spine so the front cover lands on top. Press the covers closed, and you have your foldy zine!

The cross-shaped paper collapses into a closed eight-page booklet.

That’s it

You made a Foldy.

Now make one with your own pages. Lay it out in Zineroo and it prints in the right page order, so every page lands where it should when you fold.

Make a foldable zine

One cut only

Where to cut a zine.

Cut along the long center crease, through the middle two panels only. On the open sheet the slit runs across the center half of the paper, and the panels at each end stay joined.

  • Letter: the slit is 5½ in long, or 2¾ in from the fold when the sheet is folded in half.
  • A4: the slit is 148.5 mm long, or about 74 mm from the fold.
  • Start at the folded edge and stop at the first crossing crease.
A landscape sheet divided into four columns and two rows. The cut runs along the horizontal center crease through the middle two columns only. cut here slit = half the sheet’s length

Which panel is which

Zine page order.

With the sheet landscape and printed side up, the bottom row reads back cover, front cover, page 2, page 3 from left to right. The top row is upside down and reads 7, 6, 5, 4.

Folded, the booklet reads front cover, pages 2–3, 4–5, 6–7, then the back cover. This is the layout the steps above are written for. Other templates sometimes mirror it, so check where your covers sit before you fold.

Page order on the flat sheet. Top row, upside down, left to right: 7, 6, 5, 4. Bottom row, left to right: back cover, front cover, 2, 3. The cut runs between the rows through the middle two panels. 7654 BACKFRONT23 printed side up · top row upside down

Free to print

Printable 8-page zine template.

A blank one-sheet template with the eight panels, page numbers and the cut line already marked. Print it single-sided at actual size (100%), fill each panel, then fold it with the steps above.

Rather type, add photos and skip the page math? Make it in the Zineroo zine maker and it prints in the right page order.

Before you fold

What you need.

  • One sheet of Letter or A4 paper, printed on one side
  • Scissors, or a craft knife and a ruler
  • A thumbnail, bone folder or spoon for sharp creases
  • A few quiet minutes

Letter and A4

Paper sizes.

SheetEach pageCut length
Letter
8½ × 11 in
2¾ × 4¼ in5½ in
A4
210 × 297 mm
74 × 105 mm148.5 mm

Everyday copy paper (20–24 lb, 75–90 gsm) folds crisply. Heavy card stock fights the folds and makes the booklet puff open.

Save a sheet

Common zine folding mistakes.

  • Cutting too far. If the slit reaches the end panels, the sheet falls into two pieces. Stop at the crossing crease.
  • Cutting the wrong crease. The slit runs along the long center crease, through the middle two panels only.
  • Printing double-sided. Every page is on one side of the sheet. The back stays blank and ends up hidden inside the folds.
  • Printing with “fit to page” on. Print at actual size (100%) so the creases land on the panel edges.
  • “Fixing” the upside-down row. The top row is upside down on purpose. It turns the right way up when you fold.
  • Soft creases. A mushy fold makes the booklet gape. Run a thumbnail along every crease.

Questions

Zine folding FAQ.

How many pages does a one-sheet zine have?

Eight: a front cover, six inside pages and a back cover, all from one sheet and one cut.

Should I print single-sided or double-sided?

Single-sided. All eight pages are on the front of the sheet. The back stays blank and ends up hidden inside the folds.

How do I number the pages?

Number them in reading order: front cover, 2 to 7, back cover. On the flat sheet that puts back, front, 2 and 3 along the bottom, and 7, 6, 5 and 4 upside down along the top (see page order). Make it in the Zineroo zine maker and it places every page for you.

What if my zine won’t close flat?

Re-crease every fold firmly, especially the spine, then press the zine under a heavy book for a few minutes. If it still springs open, check that the cut stopped at the crossing crease and that the paper isn’t too heavy.